Responsible of the all Installation and commissioning jobs related to Mechanical & Plumbing and HVAC system.
Responsible of the all Installation and commissioning of centrifugal pumps and chillers related to Mechanical & HVAC system
Assist and Report about daily basis activities related to Project Execution to Senior Engineer and Project Manager.
Manage the work force and arranged the all required     materials, pipes with fittings and spare parts.
Arrange and implement the all safety protocols.
Facilitate to subordinates for problem solving arise related MEP and HVAC during project construction.
Validates design issues related to MEP and suggest alternative solutions
Project planning, cost estimation. procurement and inventory management.
Study and Implementation of the Engineering  construction drawings
Involved with project consultant in all Inspections related to Project installation.

 Performed the Major Turnover at LDP-3 Plant in Qatar Petrochemical Company Qatar.

Responsibilities:

Overhauling of the Booster Reciprocating (PD) Compressor (289bar) Double Acting with six stages of Burckhardt compression Switzerland Company.
Study of the Engineering Drawings.
Performing the all shutdown activities hands on experience by using different tools and techniques.
Involved in all Inspections of the Machine with Vendors.
Check the all clearances
Web deflection of crank shaft
Bearings clearances
Runout of the piston rod
Check the TDC and BDC of piston  

Performed the Major Turnover at pearl GTL Plant (oil and gas) in Qatar through Sulzer Rotating Equipment Services Company Qatar.• Major overhauling of the steam turbine which runs two (HP and LP) syn gas compressors from its LP and HP side.• Minor overhauling (Replaced the Dry Gas seals and all O-Rings, inspection of the Axial thrust bearing and journal Bearings) of LP and HP syn Gas compressors.• Taken the all required measurements ( Axial thrust, float, centering and run out of the Rotor) • Involved in Alignment of the Machines,• Performed the all shutdown activities hand on experience by using different tools and techniques.• Study of the technical Assembly and Dismantling drawings • Involved in all Inspections of the Machine with Vendors

Performed the Major Turnover at LDPE-1 Plant in Qatar Petrochemical Company Qatar through Brunel oil and gas services W.L.L Company Qatar.• Major Overhauling of the Single Screw Extruder with Barrels, Pelletizer and Gear Box.• Performed the all shutdown activities hand on experience by using different tools and techniques.• Study of the technical Assembly and Dismantling drawings • Involved in all Inspections of the Machine with Vendo

                 Mechanical Rotating Technician (2nd Feb 2020 to 16th March 2020 )
                 Brunel oil and gas services W.L.L Company Qatar.
 It is approximated 2 month turnover at LLDPE Plant of the Qatar petrochemical company (QAPCO).Performed the Shutdown with Brunel company in Qatar Petrochemical company (QAPCO).performed the following tasks.
o   Overhauling of the twin screw extruder with barrels and Palletiser of German Coperion Company.
o   Study of the technical assembly and dismantling drawings and P&I of operations sequence of the plant.
o   Study of the commissioning and installation drawing of the plant accessories and axillaries system.
o   Performed the all shutdown activities hand on experience by using different tools and techniques.

It was one year training program; started from the Operations Dept. It was three months orientation, where I was offered to learn the basics of Combined cycle Power Plant, BOP systems, Gas Turbine, Heat Recovery, and Steam Turbine Systems. The learning perspective of systems was based on: Purpose of system, Process Flow (P&ID), Equipment used, Detailed Description, Factors effecting on the system, and Limitations of systems. After three months orientation of Operations Dept., switched to the Mechanical Maintenance Dept. Started from the learning of safety protocols, safety procedures, use for the performing different maintenance activities at plant. I have been engaged on daily basis activities (CM & PM), starting from the generating a job request, placing the work orders, generating the work risk assessment reports, till the execution of the work activity, and cancellation of work permit. Beside of that, soft skills are also being considered to improve, such as technical report writing, Maximo operation, and excel work sheet, my technical knowledge, hands on experience upon mechanical activities are as fallow:
o   Routine base PMs and CMs on gas turbine, steam turbine and HRSG.
o   Shaft alignment methods
o   Bearing clearances measurements
o   Backlash of gearing mechanism
o   Overhauling and troubleshooting of pumps (Centrifugal and   Reciprocating)
o   Troubleshooting of compressor (Rotary)
o   Maintenance of valves, filters and heat exchanger
o   Maintenance of Demineralized water Trains and Clarifiers
Performed Major Inspection (Three Shutdown) of Gas turbine Frame 9E. (10 Oct 2019 to 20 Nov 2019).
o   Inspection (NDT) and  maintenance of  HRSG (HP ,IP LP Drums)
o   Inspection and maintenance  of valves ( globe valve, gate valve , none returns valve ,ball valve, butter fly valve, MCV  and diaphragm valve)
o   Inspection and maintenance cooling tower
o   Inspection and maintenance of cooling tower gear box
o   Check Cooling tower fan angle and track as well. 
o   Performed shaft alignment by using Rim and Face method and check shaft Run out.
Monitor and inspect the Rigging with crane (SWL) of capacity (360, 200, 100, 50 ton) lifted the weight 5 to 35 ton.